The Short Answer
The fastest way to organize screws and bits on your tool belt is to use two pieces together: a closable pouch for bulk hardware, and a magnet for the screws and bits you're using right now. The pouch keeps everything from spilling. The magnet keeps your next screw or bit in sight, so you stop digging.
Our picks are the Holstery Joey Pouch, a compact clip-on pouch with a cinch top that stays closed when you climb and crawl, and the MagMaster, a clip-on N52 magnet rated to hold 5+ lbs. Both clip onto any belt up to 1.75" wide, both are assembled in the USA, and both are backed for life.

Jump to a section
In This Guide
Why Screws and Bits Get Lost on Your Tool Belt
There are countless types of screws and fasteners, and even more ways to carry them. Traditional tool belt pouches, a dedicated nail bag, a hammer holder with bit slots: whatever you use, small hardware tends to end up buried at the bottom or spilling out the top when there's no secure closure.
As your belt grows, it gets harder to keep track of the small but critical parts that keep a job moving. Fixed, stitched-in layouts limit where you can put your hardware. One minute you need screws up high, the next you want them lower for better reach. When your setup can't adapt, you lose time.
The fix isn't more space. It's smarter organization.

Pouch vs. Magnet: What Each Does Best
Hardware pouches
- Pros: Hold a lot, carry non-magnetic parts like brass screws and plastic anchors, and keep a mix of hardware in one place.
- Cons: Open-top pouches spill when you bend over, and deep pouches make you dig.
Magnetic holders
- Pros: Screws and bits sit on the outside where you can see and grab them. Nothing to dig through, nothing to spill.
- Cons: Only hold steel, and less total capacity than a pouch.
That's why the best setups run both.
Open Nail Pouch vs. Joey Pouch vs. MagMaster
| Open-Top Nail Pouch | Holstery Joey Pouch | Holstery MagMaster | |
|---|---|---|---|
| Best for | Bulk nails on the ground | Bulk screws, small parts, non-magnetic hardware | The screws and bits you're using now |
| Spills when you bend | Often | No, cinch top closes | No, magnet holds |
| Finding the right part | Dig for it | Compact, easy to reach in | In plain sight |
| Holds non-magnetic parts | Yes | Yes | No, steel only |
| Placement | Usually fixed | Clip anywhere, ModSlots on the sides | Clip anywhere, belt or pouch |
| Rating | Varies | 4.8/5 (600+ reviews) | 4.8/5 (900+ reviews) |
| Price | Varies | $45 | $30 |
The Joey Pouch: A Screw Pouch That Stays Closed
A good clip-on pouch should be secure, easy to place, and simple. The Joey Pouch is a compact belt clip pouch with a cinching top that keeps screws, bits, and small hardware inside, even when it's filled to the brim.
Unlike open-top tool belt pouches, the Joey Pouch stays closed when you're climbing, crawling, or moving fast across a job site. You get the simplicity of a compact nail pouch with a real closure, plus ModSlots on both sides for mounting a holster or a MagMaster right on the pouch. As one verified buyer put it: "I love to be able to close my holster pockets so that my stuff doesn't fall out" (David V.).
Need more room or tougher materials? The Big Joey Pouch adds capacity without the bulk of a full nail bag. The Joey Pouch Pro steps up to 1000D Cordura nylon, an aluminum backer, a spring steel clip, and a tough UHMWPE liner.

The MagMaster: A Drill Bit and Screw Holder for Your Belt
Drill bits are a similar headache. Some belts have bit slots, while others leave you dropping bits into a general pocket and hoping they stay put. The MagMaster is a high-strength magnet that clips onto your belt or pouch wherever you need fast access. It keeps your most-used bits, screws, and steel tools visible and within reach, so you're not patting yourself down for that one bit.
"Great addition to keeping bits handy in between uses" (Wade G., verified buyer)
Move it as your work changes
Unlike a magnet sewn into a fixed holster, the MagMaster can be repositioned any time. Mount it next to your hammer holster for quick fastener access, beside your tape holster for layout work, or right on your Joey Pouch, where it fits the ModSlot on the side. One buyer called it a "Fantastic addition to the joey pouch." (Jesse H.)
Use more than one
Run two or three MagMasters to separate screw sizes or bit types. You get a clear visual system that cuts mistakes and wasted motion.


Want both at once? Build a kit and save 10% →
How to Organize Screws and Bits on Your Tool Belt
- Sort by how often you reach for it. The screws and bits you use every few minutes go on a magnet. Bulk supply goes in a pouch.
- Put the magnet on your dominant side. Place it near the tool you use those parts with, like your drill holster or hammer.
- Close up the bulk. Keep spare screws, anchors, and non-magnetic parts in a pouch with a closing top, so nothing spills when you bend.
- Separate sizes with multiple magnets. One for wood screws, one for bits, one for a steel hand tool.
- Reset by the task. Move pouches and magnets as the job changes, instead of carrying hardware you don't need.
Joey Pouch
A compact clip-on pouch with a cinch top that keeps screws from spilling.
Shop now →Joey Pouch Pro
1000D Cordura, an aluminum backer, and a tough UHMWPE liner.
Shop now →Big Joey Pouch
More room for bulk fasteners, without the bulk of a full nail bag.
Shop now →MagMaster
An N52 magnet rated 5+ lbs that keeps bits and screws in plain sight.
Shop now →MagMaster Pro
The same N52 magnet on an aluminum backer and steel clip.
Shop now →ModPouch
Hand tools inside, a MagMaster or holster on the ModSlots outside.
Shop now →ModPouch Mini
A small hub pouch for light calls and a few fasteners.
Shop now →PinPal
A gravity locking drill holster, so your bits and your drill stay together.
Shop now →Example setups
- Cabinet and trim install: Joey Pouch for screws, one MagMaster for bits, one for trim screws.
- Electrical service: Joey Pouch for wire nuts and device screws, MagMaster for bits.
- Deck or fence day: Big Joey for bulk screws, MagMaster for bits and the screws in use.
- HVAC call: MagMaster for sheet metal screws and a nut driver, Joey Pouch for everything else.
Which Should You Choose?
If screws keep spilling out of your pouch... switch to a Joey Pouch. The cinch top stays closed.
If you keep losing bits... add a MagMaster. Your bits stay on the outside, in plain sight.
If you carry a lot of bulk fasteners... get the Big Joey Pouch, and add a MagMaster for what you're using now.
If you're hard on gear... go Pro: the Joey Pouch Pro and MagMaster Pro use aluminum backers and steel clips.
If you want both, organized your way... run a Joey Pouch with a MagMaster in its side ModSlot.
Our Pick: Holstery Joey Pouch
Joey Pouch | Clip-On Tool & Hardware Pouch
A compact clip-on pouch with a cinch top that keeps screws, bits, and small parts inside when you climb and crawl. ModSlots on both sides hold a MagMaster or holster.
- Assembled in USA
- Lifetime repair or replace guarantee
- 45-day money back
- Free USA shipping over $99
$45
Shop the Joey Pouch →Complete the system: add a MagMaster →
Common Concerns
"A cinch top will slow me down."
It opens and closes quickly, and it saves you more time than it costs by keeping hardware off the floor. Keep the screws you're using on a MagMaster, and the pouch only opens when you restock.
"Will a magnet hold my bits when I move?"
The MagMaster's N52 magnet is rated to hold 5+ lbs, far more than a handful of bits and screws.
"Magnets don't hold brass or stainless screws."
Right, magnets only hold steel, and some stainless grades won't stick well. Carry those in the Joey Pouch.
"I already have a tool belt."
Keep it. The Joey Pouch and MagMaster clip onto any belt or strap up to 1.75" wide.
FAQ
How do you organize screws on a tool belt?
Keep bulk screws in a closable pouch and the screws you're using now on a clip-on magnet. Use separate magnets for different sizes.
What's the best way to carry drill bits on a tool belt?
A clip-on magnet like the MagMaster keeps bits visible and within reach instead of loose in a pocket.
Does the Joey Pouch close?
Yes. It has a cinching top that keeps screws and small parts inside when you climb, crawl, or bend.
Can I put a MagMaster on my Joey Pouch?
Yes. The Joey Pouch has ModSlots on both sides for a MagMaster or any Holstery holster.
What's the warranty?
Every Holstery product comes with a lifetime repair or replace guarantee, a 45-day money back return, and free USA shipping over $99.
Stop Digging. Start Working.
The bigger your setup gets, the easier it is to lose small hardware in an oversized pouch. You can keep working around a fixed layout, or build a modular system that works the way you do. Stop digging through deep compartments. Stop losing that one critical bit. A secure pouch backed by modular magnetic organization turns your tool belt into a system that works with you.